How To Rebuild An 18v Dewalt Battery

How To Rebuild An 18v Dewalt Battery

Rebuild Dewalt 18v BatteryAs most people have seen, you can buy a book for roughly $6 that will show you how to “Bring your dead battery pack back to life!”  But unfortunately, for any of us that have actually tried the method that they show you, it doesn’t work.

They basically tell you how to zap your battery pack with 24 volts and it will make your battery like new again.  I don’t suggest buying those books to anyone.

It’s a waste of money.

I decided to start a blog, and show people how to properly rebuild batteries, and answer any questions that people may have about the subject.

My name is Brad.  I own a battery repair shop in Escondido California called FixMyBatteries.com.

Best Battrey Rebuilders

I have built virtually every type of cordless tool battery you can think of, and they are basically all the same.

So the method that I describe in this post, will work for any type of NiCd (Nickel Cadmium) or NiMH (Nickel Metal-Hydride) battery pack.

The first thing you need to do is get the cells, nickel strips, and a size T-10 Torx bit for your screwdriver or screw gun.

I use an industry specific spot welder to rebuild batteries in my shop, but I am going to assume that most people will be using a soldering iron.

If you don’t have a soldering iron, you can pick one up at any electronics store for about $20. You will also need rosin core solder.

Step 1:

Unscrew Dewalt Rebulid The Battery

If you look at the top of the 18 volt DeWalt battery you will find that there are screws holding it together.  Remove the screws from the top of the pack and carefully remove the lid from the base of the pack.  Inside you will find 15 – 1.2volt Sub-C size cells.

Rebuild Drill Battery

Step 2:

Carefully remove the insulation from the top and bottom of the battery cells.

You will see that the battery cells are connected together using strips of nickel from Positive to Negative (wired in series) which is what creates the 18 volts of electricity.

Step 3:

Carefully remove the top cell.  To do this you will have to break off the piece of Nickel that connects the bottom of the cell to the rest of the pack.

Then you will see a wire goes from the black connector down to the pack and is connected to the positive terminal of one of the cells.

Using your soldering iron, remove the thin black wire (the Thermistor) from the side of the top cell.

At this point the only thing still connected to the top cell is the connector for the drill.

Using something flat, like a putty knife, pry up where it is connected to the battery cell.

Step 4:

Now you have the pack disassembled.

Set the pack on the table, and next to the pack, set up your new battery cells in the same configuration as the old pack.

It’s not a bad idea to tape or glue the new cells together, so when you’re soldering the nickel tabs on, you don’t move the configuration of the cells.

Step 5:

Use a marker to write on the top of the new cells, marking the way the nickel strips connect the batteries together.

It’s important that you do this part correctly.

If you make a mistake and complete the circuit on the new cells, you will most likely burn yourself, and you will definitely ruin your new cells.

Mark the top and the bottom of the battery pack.

Step 6:

Use your soldering iron to solder the nickel strips in place.

If you have never used a soldering iron before, it’s a good idea to Google it!

Watch a video or two to make sure you know what you’re doing first!

Step 7:

Replace the insulators on the top and the bottom of your new pack.

Step 8:

Connect the positive terminal of the top cell, to the negative terminal of the pack with nickel and solder.

Step 9:

Solder on the black connector to the negative terminal of the top cell.

Be careful not to use too much solder because if you do, you will have a hard time getting the battery pack to fit properly in the case.

Step 10:

Solder the thin black wire on to the side of the top cell.

Step 11:

Solder the white wire on the front of the battery connector to the positive terminal on the pack.

Step 12:

Put the pack in the case and replace the top of the case.

Be careful not to tighten the pack too much or you will likely strip out the screws and the pack won’t stay together properly.

And that’s it.

You’re done!

Rebuild Dewalt 18v Battery

Put your battery on the charger and make sure it is charging properly.

If it is not, then you probably did something wrong, and will need to re-trace your steps and make sure you followed the instructions perfectly.

If you have any questions feel free to comment.

If this seems like to much of a pain … you can check out my website at FixMyBatteries.com, follow the simple instructions for ordering a battery rebuild and I will do it for you!

I don’t have a camera in the shop, but did have these couple of pictures to put up

I plan to add more pictures to go along with these instructions soon.

Be Careful … and Good Luck!

Did you try it – how did it work out?

Share and Enjoy:
  • Print
  • Digg
  • Sphinn
  • del.icio.us
  • Facebook
  • Mixx
  • Google Bookmarks
  • Blogplay
This entry was posted in Cordless Drill Batteries, Cordless Drill Battery Parts, Cordless Drill Battery Rebuild, Cordless Drill Battery Rebuilding, Cordless Drill Battery Repair, Cordless Drill Battery Service, Cordless Tool Battery Repair, Rebuild Cordless Drill Batteries and tagged , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , . Bookmark the permalink.

2 Responses to How To Rebuild An 18v Dewalt Battery

  1. Steve Crawford says:

    Man – I’ve been looking for this info.
    It worked … thank you, thank you!

  2. Pingback: Rebuild Battery Packs For Cordless Drills and Power Tools | Fix My Batteries Blog

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>